A 7″ Android display for the helm or the chart table. Run the Nauti-Control app on it for live instruments and autopilot control from your Nauti-Control controller, and your chart apps (Navionics, Savvy Navvy, OpenCPN) alongside. It’s wired into the boat’s 12 V or 24 V supply, so it’s always on the helm and your phone stays in your pocket.
- Nauti-Control dashboard and autopilot control on a fixed screen at the helm
- Google Play Store: install Navionics, Savvy Navvy, OpenCPN and other marine apps
- Mounts landscape or portrait
- Powered from the boat: no internal battery to charge or wear out
- Works with both the ST Wireless and N2K Wireless controllers
Clamped to the pushpit. The screen was recorded on our test bench.
Save 10% with a controller. Buy the M22 with an ST Wireless or N2K Wireless controller and get 10% off the display. The discount is applied automatically in your basket.
Your instruments and autopilot at the helm
The Nauti-Control app connects to your controller over Bluetooth and shows heading, depth, wind, boat speed, course and rudder on a dashboard you arrange yourself. The autopilot page gives you Standby, Auto, Wind, Track and 1° / 10° course changes, where your pilot supports those modes.
The Nauti-Control dashboard, recorded on our test bench.
On the handle by the hatch, showing the autopilot page (recorded on our test bench).
Your chart apps on the same screen
The M22 runs Android with the Google Play Store, so you can install the navigation apps you already use, including Navionics, Savvy Navvy and OpenCPN. Each needs its own account or charts.
The Nauti-Control app’s own map, recorded on our test bench.
Landscape or portrait
Mount it either way round. In portrait, the Nauti-Control dashboard switches to two columns.
Portrait, recorded on our test bench.
Specifications
- Screen: 7″, 1024 × 600, touch, up to 500 nits, with a sun hood
- Android 13 with Google Play Store
- Processor: Allwinner A523, 8 × Arm Cortex-A55 (4 × 1.8 GHz + 4 × 1.42 GHz)
- Memory: 2 GB RAM, 32 GB storage, microSD card slot (card not included)
- Wi-Fi and Bluetooth
- GPS + BeiDou receiver with external antenna
- Power: 12-24 V DC, about 1.5 A max at 12 V. Switches off below 11.6 V to protect your battery. No internal battery
- Water resistance: IP67 (dust-tight, and waterproof to 1 m for 30 minutes)
- Storage temperature: −20 °C to +70 °C
- Size: 185 × 117 mm (width × height, including the sun hood)
What is included
- M22 MFD 7 display
- Power lead with inline 12-24 V converter (red, black and yellow wires, fork terminals)
- Ball-joint mounting arm with a tube clamp, for a guardrail, pushpit, arch or grab rail
- External GPS antenna
- Online quick start guide for boats (QR code on the box)
Fitting
Connect the black wire to the negative busbar and the red and yellow wires to a fused (3 A), switched circuit on your panel, so the display switches on and off with that breaker. The quick start guide has the full wiring diagram.
The tube clamp on a cabin-top grab rail.
Questions
Do I need a Nauti-Control controller?
For instruments and autopilot control in the Nauti-Control app, yes. The controller sends the boat data and the M22 shows it. Chart apps such as Navionics work on their own.
Is it waterproof?
Yes, the display is IP67, so it’s fine in the cockpit. Keep the power converter and cable joints somewhere dry, such as behind a bulkhead or in a locker.
Does it have a battery?
No. It runs off the boat’s supply and switches off with its breaker.
What warranty does it have?
12 months against manufacturing defects, return to base (see our terms). For help or a return, email admin@nauti-control.com.
The M22 and Nauti-Control are supplementary aids, not safety-critical navigation equipment. The skipper stays responsible: keep a proper lookout.
Reviews
There are no reviews yet.